Zebra z4m z6m printer service repair manual. Zebra Z4M Plus Drivers, Software & Manual Download For Windows 2019-01-24

Zebra z4m z6m printer service repair manual Rating: 5,2/10 801 reviews

Zebra Z4M Plus Drivers, Software & Manual Download For Windows

zebra z4m z6m printer service repair manual

Included are specifications of the printer and a brief explanation of each component and its function. A wide range of paper, polypropylene, polyester, and vinyl stock has been specifically engineered to enhance the printing capabilities of the printer and to ensure against premature printhead wear. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the menu. The incorrect media sensor is being used. Flashing returns to normal rate when the data input buffer is no longer full and data is again being received.

Next

ZEBRA Z4M/ZEBRA Z6M Service Manual :: ZEBRA

zebra z4m z6m printer service repair manual

Set the pressure to the minimum required for good print quality. Front Cover and Electronics Cover Removal Reinstall the latch cover. Hold the cutter assembly as far to the left as possible, align the larger part of the slot with the hooks on the platen housing. Remove the media and ribbon if loaded. Ensure that they match the printer settings. Value Peel Assembly Mounting Slots Pems Figure 4-69. Tear Bar Tear Bar Mounting Screws Figure 4-55.

Next

Zebra Z4M/Z6M Printer Workshop Service Repair Manual

zebra z4m z6m printer service repair manual

Wind the ribbon clockwise onto the ribbon take-up spindle. Work the inboard bearing back and forth until the bearing is up against the clip. The manual contains all you need to know to keep your photocopier working right. Liner Take-up Motor Assembly Mounting Screws Figure 4-61. Slide the front cover to the right, then lift to remove.

Next

Zebra Z4M/Z6M Printer Workshop Service Repair Manual

zebra z4m z6m printer service repair manual

Press the printhead open lever. If a value peel assembly is not currently installed the tear bar must be removed. The printhead assembly springs up. Tighten the adjustment screw until the top of the strike plate is just below the top of the ribbon guide plate. . Close the pivot bracket assembly.

Next

Zebra Z4M/Z6M Printer Workshop Service Repair Manual

zebra z4m z6m printer service repair manual

Hold the ribbon snug and free of wrinkles and in line with the guide mark near the left edge of the ribbon guide plate. Replace the washer and mounting screw onto the shaft. Removal of the Drive Belt 77259L Rev. Printhead Grounding Strap Printhead Grounding Screw Figure 4-6. Slide the rewind media guide against the media, and tighten the thumbscrew to lock it into position.

Next

Zebra Z4M/Z6M Printer Workshop Service Repair Manual

zebra z4m z6m printer service repair manual

The Small Part Facing Out. Disconnect all connectors from the main logic board. We strongly recommend the use of Zebra Technologies Corporation-brand supplies for continuous high-quality printing. Remove the four screws that attach the main frame to the base. Slide the liner from the take-up spindle.

Next

ZEBRA Z4M MAINTENANCE MANUAL Pdf Download.

zebra z4m z6m printer service repair manual

Rewind Motor Assembly Mounting Align the other access hole of the rewind back plate to the other mounting hole on the rewind support. Print Mechanism Unlatch the print mechanism. . Tighten the two screws on the rear of the main frame. Close the value peel assembly.

Next

ZEBRA Z4M MAINTENANCE MANUAL Pdf Download.

zebra z4m z6m printer service repair manual

Reconnect power cord to the printer and restore power. . If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. Connect one end of the supplied cable assembly to P3 on the main logic board Feed the other end of the cable assembly through the access hole in the base of the main frame. Take note of the pems and the mounting slots.

Next