Electrical engineering job test questions. ELECTRICAL ENGINEERING 875 OBJECTIVE QUESTIONS AND ANSWERS IN ONE PDF 2019-02-25

Electrical engineering job test questions Rating: 4,2/10 256 reviews

Electrical Engineering Interview Questions

electrical engineering job test questions

Power Quality meters are common in many industrial environment. Fuses are burned at the time of over current flows in the circuit but breakers are just open not burn at the time of over current flow. That is; surge protectors that turn the current back on when the surge is over. Speed of the rotor of an induction motor is always less than its synchronous speed. So if any short circuits occur in the system first high currents bypassed in the Earthling terminal. Both have the same principle of electromagnetic induction, the only difference is that their construction. A fixed width pulse is generated for each cycle.

Next

Electrical Engineering test questions for exams and entrance

electrical engineering job test questions

The telephone company has been using regenerative surge protectors for over forty years. Do You Have a Specialty? Mention what are a different kind of cables used for transmissions? Thin film resistors- It is constructed as a thin film of resistive material is deposited on an insulating substrate. Output voltage is greater than the input voltage or receiving end voltage is greater than the sending end voltage. T means current transformer,and the term P. Only one of the terminals is evident in the earth resistance. It is a speed at which any system take small current and give maximum efficiency. Resolution:4-20 mA is a standard range used to indicate measured values for any process.

Next

Engineer Job Interview Questions

electrical engineering job test questions

Mention the methods for starting an induction motor? Hysteresis loss is constant for a particular voltage and current. Will you be able to do the work? It is the property of a cable by virtue of it can withstand the applied voltage without rupturing it is known as insulation level of the cable. This includes the maximum power of the network and in this case, the load resistance is being been equal to the resistance of the network and it also allows the resistance to be equal to the resistance of the network. These losses depend upon the supply voltage, frequency, core material and its construction. Its value depends upon the speed of rotation of the armature conductors. It is the resistance offered by a diode to the changing forward current.

Next

Electrical Engineering test questions for exams and entrance

electrical engineering job test questions

Which type of motor is used in trains, what is the rating of supply used explain Working principal? Particularly when a measuring device like voltmeter or ammeter is not able to measure such high value of quantity because of large value of torque due to such high value it can damage the measuring device. Hence in control systems negative feedback is considered. During this process, the value of the resistance is monitored closely and cutting of grooves is stopped as soon as the desired value of resistance is obtained. You can see that most questions the interviewers will fire at you will be tests. Your installation of conductors will depend on a few factors like gauge of the wire, wire capacity, etc. Thus is due to negligible small leakage current. What is 2 phase motor? It is an inverse definite minimum time relay.

Next

Electrical Test Engineer Jobs, Employment

electrical engineering job test questions

I have been searching for an answer on line for several hours and cannot find any discussion of this subject. Design of all power equipments also comes under power engineering. I did equally well in the majority of my university's electrical engineering computer software classes. So it should be zero lagging like inductor. This effect of supporting and opposing of main flux to armature flux is called armature reaction. What is the use of stepper motor? State the difference between generator and alternator Generator and alternator are two devices, which converts mechanical energy into electrical energy.

Next

Electrical Interview Questions updated on Mar 2019

electrical engineering job test questions

Desired results are obtained by either trimming the layer thickness or by cutting helical grooves of suitable pitch along its length. Essentially dc motors are utilized for electric traction systems. Reliability: It is the capacity of the power system to serve all power demands without failure over long periods. What is reverse power relay? If it persists, a licensed electrician will be needed. Explain thin film resistors and wire-wound resistors Answer — a Thin film resistors- It is constructed as a thin film of resistive material is deposited on an insulating substrate.

Next

ELECTRICAL ENGINEERING 875 OBJECTIVE QUESTIONS AND ANSWERS IN ONE PDF

electrical engineering job test questions

Hence the starting current is reduced , the voltage drops during the starting of motor in systems are reduced. Therefore, it is suitable for constant speed drive, where high starting torque is not required such as pumps, blowers, fan, lathe machines, tools, belt or chain conveyor etc. The resistance of the electrode has the following components: A the resistance of the metal and that of the connection to it. And structure is also to be earthed, so can I connect both lightening arrestor earthing and structure earthing together? The output terminals are equivalent to the constant source of current and it allows giving the parallel resistance. The current currying of cables will change depending upon the site temperature location of site , type of run it will run through duct, trench, buried etc. When a string of resistors in a series will divide the source voltage into proportion to their values. B the contact resistance of the surrounding earth to the electrode.

Next

Electrical Engineering Interview Questions and Answers

electrical engineering job test questions

Hence the starting current is reduced , the voltage drops during the starting of motor in systems are reduced. Answer — If the resistance total in a series circuit doubles the current will reduce to half. However, previously we had provided the. Combustion-resistant vegetable oil-based dielectric coolants and synthetic pentaerythritol tetra fatty acid C7, C8 esters are also becoming increasingly common as alternatives to naphthenic mineral oil. This reduces the amount of noise injected into the amplifier, because any noise appearing simultaneously on both the input-terminals as the amplifying circuitry rejects it being a common mode signal. It is the property of a cable by virtue of it can withstand the applied voltage without rupturing it is known as insulation level of the cable. Name the types of motors used in vacuum cleaners, phonographic appliances, vending machines, refrigerators, rolling mills, lathes, power factor improvement and cranes.

Next

300+ TOP ELECTRICAL ENGINEERING Interview Questions & Answers

electrical engineering job test questions

What is a differential amplifier? This type of generators are used in windmills. What is reverse power relay? Motor generator set is also referred to as a genset, or more commonly, a generator. Both generator and alternator work on the same principle they convert mechanical energy into electrical energy. Reactance is the resistance offered to the ac currents by inductors and capacitors only. What happens when two positively charged material is placed together? Operation carried out in Thermal power stations? Define what is difference between fuse and breaker? Enlist types of dc generator? Mutual inductance happens when a secondary coil opposes the current change in the primary coil. Capacitor is load free component but why ampere meter shows current when capacitor bank breaker close? Thus it can control the output Reactive Power of the Generator. For example, low voltage lighting and lamp cords will have 18 gauge, electric furnaces or large electric heaters are of 6 gauge.

Next