Secure the rear arm to the support bracket with the 7. Arctic Cat Snowmobiles service manuals are available for immediate download! Remove the lock nuts and rocker arm pivots secur- 16. Ski Center-to-Center 78 cm 31 in. After replacing the spark plug with a colder type, tune the carburetors again. This section has been organized for servicing the fuel 1. Inspect the ball joint pivot to the spindle account for the washer ; then area for wear. Remove the lock nut, washers, and cap screw securing the end cap.
Arctic Cat rec- storage, lubricate the spindles and ommends the following procedure to the rear suspension with an all-tem- prepare the snowmobile. Using light pressure, move both sides in a figure eight motion. The valve seat and body must be replaced as a set Power loss Broken float Replace the float. Clean all compound residue from the valve and diameter readings on the valve stems and inside seat. Check all control wires and cables for signs of Torque Specifications wear or fraying.
Remove the bulb from the housing The headlight aim can be adjusted to pro- by rotating it counterclockwise until vide maximum illumination for the oper-. Overflow Adjust the fuel level. This manual is divided into sections. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Starting with the top ring, slide one end of the ring out of the ring-groove. Melted electrodes and possibly a blistered insulator Metallic deposits on insulator Mixture is too lean.
The sections cover specific snowmobile components or systems and, in addition to the standard service procedures, includes assembling, disassembling, and inspecting instructions. Moreover, we are in fact owners of intellectual property, property that is a valuable asset to our business. Dirty or clogged fuel line Clean or replace the fuel line. With a gasket in place on the intake tube, install 3. Remove the C-clips securing the brake and throttle the throttle control;.
Check the connecting rod side clearance by using a thickness gauge. Compress and hold the brake lever; then install the damage. Place the oil ring expander into the bottom groove of the piston allowing the ends to contact each other. This form may also be used to transfer the unused portion of the original warranty to a second party. This 2008 Arctic Cat 366 repair manual was designed to aid the mechanic 17. Always use these numbers when referring to your snowmobile.
Poor performance at Clogged air vent Remove the air vent hose and clean it. It is fully printable, print 1 page, 1 chapter or print the entire manual and put it in a 3-ring binder. All of the manual listed below are full factory service manuals with hundreds of pages containing step by step instructions, full wiring diagrams and detailed illustrations on how to repair, rebuild or maintain virtually anything to your sled. Install the new bulb into the hous- harness connector from the head- ing; then rotate the bulb clockwise to light bulb. All of the procedures in this manual are organized in a sequential, step-by-step format.
Insert the wear bar studs into the ommends that the ski wear bars be holes in the ski. Install the hood cable and the front clutch shield. Remove the C-clip securing the throttle cable in 2. See the specifications Periodically, the brake band should be chart for the correct spark plug. With the connecting rod, end cap, and crankshaft journal lubricated with engine oil, install the con- necting rod and rod end cap to the crankshaft and secure with the cap screws. Clogged intake Remove any obstructions e. Your safety is our concern and close to roads, buildings, trees, other must always be yours.
For consistency purposes, this section shows a complete and thorough progression; however, for efficiency it may be preferable to remove and disassemble only those components needing to be addressed and to service only those components. Replace main jet with a larger size. Clearance measurement must be within 0. Inspect the chain and chain sprocket for damage or wear. Service Repair Manual Covers: 1.
Route the cable through the slot in the throttle con- trol and insert the cable into the throttle control. Remove the idler wheels from the axle and inspect for binding or roughness. Inspect the driveshaft sprockets for wear or damage. Inspect the sealing surfaces for trueness by placing each on the surface plate covered with 400 grit wet-or-dry sandpaper. Air leaks into the fuel line Tighten or replace the fuel line joint. Use cable ties or tape to route wires and cables away from hot or rotating parts.
At this point, scribe a line at the front of the engine 13. Place the end cap onto the rail and secure with the cap screw. Clogged or loose main air jet Remove the main jet, clean it with compressed air, and then install it. Most all service manual chapters start with an assembly or system illustration, diagrams, exploded parts view, quality pictures, service information and troubleshooting for the section. Apply an all-temperature grease to remove the ball joint from the spindle. Arctic Cat Snowmobiles service manuals - the easy way! Follow the Maintenance Schedule recommendations to ensure that the snowmobile is in peak operating condition. Overflow Adjust the fuel level.