Get access to our 2010 Scion xB repair information right now, online. Separate the 2 wire harness clamps. Check that the bearing is not rough or worn. Scion Xb Service Repair Manual Software Pdf can be very useful guide, and Scion Xb Service Repair Manual Software Pdf play an important role in your products. If the electrolyte level is low, replace the battery or add distilled water and check the charging system. Install the terminal insulator onto the generator rectifier end frame. Getting the same information in digital format is so much less expensive and more convenient! This will remove the surface charge from the battery.
In this case, increase electrical load by operating devices such as the wiper motor and rear window defogger. Start the engine and check that the light goes off. If the condition is not good, repair or replace the generator wire. Now you can get your repair manual in a convenient digital format. If the brush length is less than the minimum, replace the generator brush holder assembly. Install the generator brush holder with the 2 screws. Remove the clutch pulley from the rotor shaft.
Remove the 3 nuts and generator rear end cover. Check that the belt fits properly in the ribbed grooves. In the dark old days of auto repair, you had to buy a traditional service manual in book format which would retail at a higher cost. Connect the positive + lead of the voltmeter to positive + terminal of the battery. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Install the generator rear end cover with the 3 nuts.
Official Service Manuals that the dealers and shop technicians use to diagnose, service and repair your Scion iQ, tC, xA, xB or xD vehicles. . Using vernier calipers, measure the brush length. Place a new generator washer on the generator rotor. Check that the charging cable nut is tightened on terminal B of the generator and the engine room relay block.
Measure the battery voltage between the negative - and positive + terminals of the battery. Install the generator wire to terminal B with the nut. Minimum diameter: 14 mm 0. Using this repair manual is an inexpensive way to keep your vehicle working properly. Check that the bearing is not rough or worn.
You probably already know this, but mechanics charge a lot. Check that the charge warning light comes on. Install a new V-ribbed belt correctly. Ground the negative - lead of the voltmeter. If you need a repair manual for your Scion, you've come to the right place. Standard current: 10 A or less Standard voltage: 13. Do not perform tests with a high voltage insulation resistance tester.
If the car has parts coming loose, will not start, is vibrating, does not shift, is stalling out frequently, is making grinding sounds, has a loose suspension, loses oil from under the engine, makes a backfiring noise, has electrical problems, is rough when the engine idles, or any other issue you could have, this product will help you resolve the problem. Go back to the page. Standard current: 30 A or more If the ammeter reading is less than the standard current, replace the generator assembly. Check that there is no abnormal noise from the generator while the engine is running. Disconnect the battery cables when the battery is given a quick charge. Then, recheck the reading on the ammeter.
Measure the resistance between the slip rings. Remove the 4 screws and bearing retainer. Install the 2 wire harness clamps. Standard resistance: Below 1 ohms If the result is not as specified, replace the fuses as necessary. Using a screwdriver, puncture the center of the generator pulley cap and pry it off.
If the diameter is less than the minimum, replace the generator rotor assembly. Pull the pin out of the generator brush holder. Temporarily install the clutch pulley onto the rotor shaft. Using vernier calipers, measure the slip ring diameter. According to the following procedure, connect an ammeter and voltmeter as shown in the illustration. Remove the nut and disconnect the wire harness from terminal B. If the terminals are corroded, clean them.
Remove the bolt and cord clip. Attach the clamp and connect the generator connector to the generator. Check the color of the indicator. Never disconnect the battery while the engine is running. Check that the clutch pulley rotates smoothly. Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate. Condition Specified condition 20°C 68°F 2.